Billy 0-4-0 chassis kit, Roundhouse #HBK1, contains the machined cylinders & all other necessary parts to build a 0-4-0 running chassis with Walschaerts valve gear for either a Ga. O & 1 engine chassis w/ full installation instructions.    HLK-1   $465.00

Billy gas fired boiler kit, Roundhouse #HBK3, contains a silver soldered single flue boiler with smokebox, brass wrapper, water level plug, S.S. superheater, safety valve, pressure gauge, displacement lubricator, gas tank, gas burner, gas control valve, throttle valve, steam oil & syringe & full installation instructions.             HLK-3    $495.00

Billy body kit, Roundhouse #HBK5, unpainted, brass sheets have all holes punched/drilled and score lines for bends.    HLK-5   $165.00

Lady Anne 0-6-0 chassis kit, Roundhouse #HBK2, contains the machined cylinders & all other necessary parts to build a 0-6-0 running chassis with Walschaerts valve gear for either a Ga. O & 1 engine chassis w/ full installation instructions.             HLK-2   $499.00

Lady Anne gas fired boiler kit, Roundhouse #HBK4, contains a silver soldered single flue boiler with smokebox, brass wrapper, water level plug, S.S. superheater, safety valve, pressure gauge, displacement lubricator, gas tank, gas burner, gas control valve, throttle valve, steam oil & syringe & full installation instructions.    HLK-4   $499.00

Lady Anne body kit, Roundhouse #HBK6, unpainted, brass sheets have all holes punched/drilled and score lines for bends.    HLK-6  $195.00

Roundhouse Boiler, 2"dia. X 6 1/2" long internal gas fired boiler with safety valve, pressure gauge, manual throttle, gas burner, gas tank, and gas regulator. Like HLK-4 but without the smokebox, chimney and superheater.    HLB-203 $ call for price
Walschaert's Valve Gear Kit (for two cylinders) Roundhouse WVG    HLV-402   $145.00
Poker Burner for Roundhouse locomotives with gas jet & mounting plate.    HLB-1   $56.00
Steam Regulator, (Throttle) for manual throttle, 3/16-40 Female Thd.    FVT-242   $28.95
Steam Regulator, (Throttle) for R/C throttle, 3/16-40 Female Thd.    FVT-242R   $28.95
Gas Regulator1/8" tube to tube.    FVT-242G   $28.95
Rectangular gas tank (without filler valve),as used on Roundhouse SR&RL #24.    HLT-1   $67.50
Rectangular gas tank (without filler valve)as used on Roundhouse Fowler.    HLT-3   $57.50
Round gas tank (without filler valve)as used on most Roundhouse engines.    HLT-2   $57.50
Lubricator, Displacement type Roundhouse LUB.    FLD-247   $23.75
Lubricator Drain Screw, Replacement screw w/o ring.    FLD-247P   $2.75
Safety Valve, 5/16"-32 Thd. Roundhouse #396    FVS-1032R   $21.50
Axle & 2 Outside cranks 1/4" dia stainless steel with squared ends complete with 2 outside cranks, 5/16" throw (self quartering).    HLP-204   $21.95
Crank pin threaded 6BA, 1/8" dia shoulder.    HLP-229   $3.75
Axle bushings Brass 1/4" bore, (pack of 4).    HLP-203   $1.85
Disc wheel 1 5/16" (33mm) dia. Steel, bored 1/4" with grub screw, nickel-plated.    HLP-328   $7.50
Frame spacer 1/4" square brass.    HLP-202   $4.50
Wheel Setting Gauge, For Ga."O" & Ga. "1", For Setting Wheel Spacing    TGW-01   $3.75
Roundhouse Cylinder Cover Gasket    HLP-485   $1.25
Roundhouse Valve Chest Gasket    HLP-248   $1.10
Roundhouse Cylinder Repair kit, all O-rings & gaskets for 2 cylinders    HLP-SK1   $11.75
Roundhouse Repair Kit for Water Hose on SANDY RIVER #24    HLP-SK2   $6.50
Roundhouse spare washers & O-ring kit for fillers, drains etc.    HLP-603   $3.25
Roundhouse O gauge conversion kit for FOWLER locomotive    HLP-703   $82.00
Roundhouse O gauge conversion kit for SANDY RIVER #24 locomotive    HLP-714  $105.00
Cylinder Covers 1 pair, painted black, used on engines made before June 1998.    HPL-681O   $18.50
Cylinder Covers 1 pair, painted black, used on engines made after June 1998.    HPL-681N  $18.50
Roundhouse Pop Valve set at 40 psi, adjustable    FVS-R-40   $22.00

SHAY GEARS  These are the Right Angle Bevel gears that are used on many commerical Gauge 1 locomotives. Gears are matched in pairs. Bevel gears of different pairs will not run together. Gears are 49 DP brass.
  3:1 Ratio gear set. Gear 36 teeth, 0.750 pitch dia. 3/16" bore, 3/32" face.    GB-116G
                                 Pinion 12 teeth, 0.250 pitch dia. 1/8" bore, 3/32" face.   GB-116P
  2:1 Ratio gear set. Gear 36 teeth, 0.750 pitch dia. 3/16" bore, 1/8" face.      GB-117G
                                 Pinion 18 teeth, 0.375 pitch dia. 1/8" bore, 1/8" face.      GB-117P

CLIMAX GEARS  These are Spiral bevel gears. Supplied as a set, one each gear & pinion with lost wax cast shaft hanger. Gear is 40 teeth with 3/16" bore, pinion is 20 tooth with 1/8" bore.    GS-1

SHAY-CLIMAX  Universal joints. (1 set is enough for a 2 truck engine)
Argyle Locomotive Universals    HLP-U1
DJB Engineering Universals       HLP-U2

LADDER CHAIN & SPROCKETS as used on the BAGRS project loco.  Chain is brass. Sprockets are brass, 0.185" pitch.
  Chain (order by the foot).   HLP-LC
  Sprocket, 7 tooth, 1/8" bore, 0.41" pitch dia.       HLP-LS7
  Sprocket, 15 tooth, 3/16" bore, 0.87" pitch dia.   HLP-LS15
  Sprocket, 24 tooth, 3/16" bore, 1.38" pitch dia.   HLP-LS24

DENVER PROJECT LOCO KIT:  Contains all the hard to find parts for the Denver Project Loco
   (3) 12 tooth ladder chain sprockets
   (1) 16 tooth ladder chain sprocket
   (1) 15 TOOTH, 48DP, 20PA BRASS SPUR GEAR
   (1) 42 TOOTH, 48DP, 20PA BRASS SPUR GEAR
   (2) Feet of 19B brass ladder chain
   (4) 1.275" dia. steel #4 Sierra Valley Enterprises wheels
   KIT-DENVER-1   $68.00

BASIC PROJECT ENGINE (BAGRS PROJECT LOCO); Kit contains all the fasteners, ladder
chain sprockets, metal stock, wheels and lubricator for the Basic Project Engine
   (2) 7 tooth ladder chain sprockets
   (1) 15 tooth ladder chain sprocket
   (1) 24 tooth ladder chain sprocket
   (2) feet of 19B brass ladder chain
   (1) #247 Roundhouse lubricator
   (1) 12" piece of 1/8" brass rod
   (1) 5/32" dia K&S brass tube
   (1) 3/16" dia K&S brass tube
   (1) 0.032" X 1/4" K&S brass strip
   (8) 2-56 X 1/2" brass model hex head
   (8) 2-56 model hex brass nuts
   (8) #2 brass washers
   (2) Sierra Valley Enterprises wheel sets
   (2) 2-56 X 3/8" machine screws
   KIT-BPE   $83.10

Gas Jet (For Roundhouse & others), Size 3, 1 BA Thread    FJG-3
Gas Jet (For Roundhouse & others), Size 5, 1 BA Thread    FJG-5
Gas Jet (For Roundhouse & others), Size 6, 1 BA Thread, most common size    FJG-6
Gas Jet (For Roundhouse & others), Size 8, 1 BA Thread    FJG-8
Gas Jet (For Roundhouse & others), Size 16, 1 BA Thread    FJG-16
Gas Jet, Primus #PCS-8925 (For Argyle & others)    FJG-89
Gas Tank Filler Valve (Ronson style) Butane gas filler valve installed in most commerical models. (4.5mm)    FVG-R
Wrench for FVG-R gas filler valve.    TWF-R
Aster Gas Tank Filler Valve type used on Aster loco's (5.0mm)    FVG-A
Tank Bushing for Gas Filler Valve, Threaded for FVG-R    FTB-VGR
Tap for machining thread on Gas Filler Valve #FVG-R if you wish to make your own bushings.   TTM-4505
Gas Control Valve (Unitshop) for tanks, requires drilling and silver soldering into tank.   FVG-S
Gas Filler Adaptor for Butane Gas Cans (Threaded Camping Style cans)- Long Neck    TGF-1
"Hadden" style Gas Filler Adaptor for GAZ Cans, (#CV270 & CV470)- Short Neck    TGF-2
"Hadden" style Gas Filler Adaptor for GAZ Cans, (#CV270 & CV470)- Long Neck    TGF-3
Cleaning Needle for Gas Jets such as FJG-X above, 0.005" Dia. wire    TN-005
WICK MATERIAL Fiberglass wick material for alcohol burners, 1/4" dia. X 3ft    MYF-3

WATER INJECTION (Goodall) VALVES: For adding water to boilers.
1/4"-26 Thd. for MAMOD Locomotives and others    FVW-0826
1/4"-32 Thd. for CHEDDAR Boilers    FVW-0832
1/4"-40 Thd for Maxwel Hemmings Porter and others    FVW-0840
3/8" X 24 Thd. for Roundhouse Classic Series Locomotives with water filling plug   FVW-RH
10mm X 1.0 Thd. for LGB FRANK "S"    FVW-1010
10mm X 1.0 Thd. for Accucraft RUBY/IDA, Shay, etc.    FVW-R
10mm X 1.0 Thd. for Accucraft C-16    FVW-C16

PUMP BOTTLE: Modified spray bottle, 24oz. with 5/32" hose for adding water to boilers of Ga. 1 locomotives through "Goodall" type valves while under steam.    TS-476

HANDRAIL KNOBS (Stanchions)
Handrail Knob, with Nut 1/4" lg. 8 BA Thd. (Roundhouse)    HHT-0825R
Handrail Knob, Short pattern, straight shank, no thd. 1/8" long, Ga. 1    HHX-1615
Handrail Knob, Long pattern, straight shank, no thd. 3/16" long, Ga. 1    HHX-1614
Handrail Knob, Long pattern, for 2 1/2" Gauge, 5/16" lg. Thd. 8BA    HHT-25
Handrail Knob, Long pattern, for 3 3/4" Gauge, 11/32" lg. Thd. 8BA    HHT-30
Handrail Knob, Long pattern, for 4 3/4" Gauge, 7/16" lg. Thd. 6BA    HHT-50
Handrail Knob, Long pattern, for 7 1/2" Gauge, 5/8" lg. Thd. 5BA    HHT-75

Nickel Silver & Brass Handrail Wire (Order by the FOOT-Specify length Required on ORDER)
0.036" Brass Handrail wire for HHX-1614 & HHX-1615    MWB-36
0.028: Nickle Silver wire    MWN-28
0.040: Nickle Silver wire    MWN-40
0.048: Nickle Silver wire    MWN-48

SPRINGS, Stainless steel compression springs for Safety valves
0.095" ID X 0.135" OD, 0.56" long.    HSL-474
3/32" ID X 0.022" dia. wire X 2" long    HSL-324
3/32" ID X 0.012" dia. wire X 2" long    HSL-330
1/8" ID X 0.038" dia. wire X 3" long    HSL-420
1/8" ID X 0.028" dia. wire X 3" long    HSL-422
1/8" ID X 0.022" dia. wire X 3" long    HSL-424

CHAIN, oval nickel plated steel chain for couplers, sold by the foot.
5 links per inch    HCL-5    3 links per inch    HCL-3

HANDWHEELS Lost wax bronze hand wheel castings. Hubs (stem) can be drilled to a maximum diameter of 3/32" or threaded 3-48 (or smaller) for the valve stem.
6 spoke with ball ends, hand wheel 1/2" dia., 0.140 stem dia.    CFH-1
Conventional web type, hand wheel 5/8" dia., 0.140 stem dia.    CFH-2

Ruby Rimmed Domes Take years off the life of your Ruby. If you have replaced the cab with a Flint Hills wooden cab or purchased one of the Forney conversion kits then these domes will help give your Ruby that 19th Century look. Includes tow safety valves and Trackside Details TD-8X whistle.
       SSSM-RD1.....$54.95

Ga. 1 LOCOMOTIVE WHEEL CASTINGS, Shell molded Cast Iron.  Wheel castings (require machining) do not have cast-in balance weight (counterweight) unless specified below. For drivers without counterweight, Dummy Cwt's can be made and glued in place.  Back of wheel requires machining to open spokes. Dimensions listed are in inches. Castings are to 1:32 scale except #HLP-W100 which is a cast iron lost wax casting (1:19 scale) for a C-16 Narrow gauge locomotive. Wheels with N or S in the part number have a wider tread and may be suitable for use on narrow gauge equipment Crankpin position on wheel:  OS is ON Spoke   BS is BETWEEN spoke. 

PART #                              O. D.of     I.D. of       #  of            CRANK     CRANKPIN Position & Description.

                                         TREAD       RIM         Spokes       THROW

HLP-W07          $7.25         1.25”           0.94”        8                n/a            None - Pilot/Trailing truck wheel

HLP-W11          $7.25         1.28"           0.94         10               n/a            None - Pilot/Trailing truck wheel

HLP-W22          $12.95       2.40"           1.93"        18               0.44"         BS - Driver, No Counterweight

HLP-W26          $8.50         1.48"           1.08"        10               n/a            None - Pilot/Trailing truck wheel

HLP-W28          $13.25       2.45"          2.10"        20                               OS - Driver, No Counterweight

HLP-W41          $8.75         1.65"           1.29"        12               n/a            None - Pilot/Trailing truck wheel

HLP-W71          $9.00         1.70"           1.27"        10               0.38"         BS - Driver, No Counterweight

HLP-W91          $10.00       1.88"           1.55"        14               0.44"         OS - Driver, No Counterweight

HLP-W92          $10.00       1.90"           1.50"        14               0.44"         BS - Driver, No Counterweight

HLP-W100        $15.50       1.91"           1.52"        9               0.5"           BS - Driver, Heavy Counterweight

HLP-WN2         $8.50         1.45"           1.10"        2(5)             0.48"         OS - Driver w/ Counterweight

HLP-WN4         $9.00         1.68"           1.20"        9               0.38"         OS - Driver w/ Counterweight

HLP-WN6         $11.25       2.00"           1.64"        10               0.38"         OS - Driver w/Counterweight

HLP-WN8         $12.95       2.21"           1.93"        12               0.5"           OS - Driver, No Counterweight

HLP-WS2         $7.75         0.80"           0.52"        10               n/a            None - Pilot/Trailing truck wheel

SERVO SMOOTHER w/ AUTOHOLD for R/C steam locomotives. This is the product to cure that glitching "Rusty Bolt" effect-the signal scatter that causes complete loss of control. Using computer technology, it sorts out the bad signals so you can really drive your steam loco. It can be set for three (3) different levels of suppression: Low 0.5 sec, Med 1.0 sec. and High 2.0 seconds. If transmitter signal is lost for any reason or turned off the device will hold the last set position. Easy to fit in-line between receiver & servos. This unit will control two (2) servos. It can be used on a single channel or two channel radio.
Small size:1.3/8" x 11/16" x 3/8". Fitted with FUTABA plugs for receiver & servos.    SAM-2AD

FUTABA STICK RATCHET: For positive (ratchet) control of joy stick to allow the centering spring to be removed & thus eliminating center condition spring back. 1 req'd per stick.
FUTABA #ST-14 for Attack II radios    HLP-14
FUTABA #ST-17 for Attack SR, supplied w/ mounting screw    HLP-17

MINIATURE PRESSURE GAUGES These precision pressure gauges are of all brass construction. They are threaded 3/16"-40 at the steam inlet. Standard practice is to use a gauge having a full scale rating of 1.1/2 to twice the working pressure of the boiler. All pressure gauges MUST be installed using a Gauge Syphon such as the ones listed below to prevent overheating. Selected size pressure gauges are available in two styles; with and without a backface flange. Without (W/O) backface flange (plain case) is the type most commonly used.

Pressure Range	Part # for 3/4" dia. case w/o flange	Part # for 3/4" dia. case w/ flange	Part # for 1" dia. case w/ o flange	Part # for 1" dia. case w/ flange
0 to 30 psi	FGX-33	N/A	N/A	N/A
0 to 60 psi	FGX-36	N/A	N/A	N/A
0 to 80 psi	FGX-38	FGF-38	FGX-48	FGF-48
0 to 100 psi	FGX-310	FGF-310	FGX-410	FGF-410
0 to 120 psi	FGX-312	FGF-312	FGX-412	FGF-412
0 to 150 psi	FGX-315	FGF-315	FGX-415	FGF-415
0 to 200 psi	N/A	N/A	FGX-420	N/A
0 to 250 psi	N/A	N/A	FGX-425	N/A

SUB-MINIATURE PRESSURE GAUGES These 1/2" diameter precision pressure gauges are of all brass construction. They are threaded 5/32"-40 at the steam inlet. Case is 1/2" diameter. Standard practice is to use a gauge having a full scale rating of 1.1/2 to twice the working pressure. A syphon is required. Available without backface flange only.

0 to 80 psi    FGX-28,
0 to 100 psi    FGX-210,
0 to 120 psi    FGX-212


VACUUM GAUGES for measuring a vacuum on condensing or brake systems. Plain case.

Range	3/4" dia. case	1" dia. case
0 to 30 in Hg	FGV-33	FGV-43

SYPHONS Complete as supplied with banjo fitting, tail cone and nut silver soldered on. Copper tube will have to be bent to the desired shape to fit your particular application.

Gauge Size	Gauge Thread Size	Boiler Thread Size	Part #
For 3/4" & 1" diameter gauges	3/16"-40	3/16"-40	FGS-640
For 3/4" & 1" diameter gauges	3/16"-40	1/4"-32	FGS-832
For 3/4" & 1" diameter gauges	3/16"-40	1/4"-40	FGS-840
For 1/2" diameter gauge only	5BA	3/16"-40	FGS-5BA
For Accucraft Ruby/Ida	3/16"-40	M5	FGS-R